After a roadside worker is struck, a photograph of cones beside an ambulance may show very little about the warnings the driver encountered. The investigation needs to reconstruct the approach before impact, the worker’s location, and the traffic-control arrangement that existed at that moment.
That requires two records: what the project called for and what the crew actually installed and maintained. They may agree. They may also differ because the work moved, a device fell, a lane closure changed, or emergency responders altered the scene. Each possibility needs evidence and timing.
Get the plan that applied to that shift
Request the approved temporary traffic-control plan, referenced standard drawings, special provisions, lane-closure permits, and revisions. Identify the project stage and direction of travel. A diagram for last week’s shoulder work may not describe a lane closure on the crash date.
The federal Manual on Uniform Traffic Control Devices, Part 6, addresses temporary traffic control. Section 6B.01 explains that plans vary with the work and road conditions; a plan may reference standard drawings or contain detailed project instructions. Sections 6A.02 and 6C.04 address inspection, changing conditions, and worker-safety considerations.
FHWA identifies the current federal edition as the 11th Edition with Revision 1, dated December 2025; its adopting rule took effect March 5, 2026. For a particular crash, establish the applicable edition, state adoption or supplement, project requirements, and relevant provision. The manual distinguishes standards, guidance, options, and explanatory material. Those distinctions matter when evaluating a claimed departure.
Compare the paper plan with the field record
Scroll horizontally to see all columns. Use the arrow keys when the table is focused.
| Evidence | Question to investigate | Detail to preserve |
|---|---|---|
| Approved plan and revisions | What arrangement was intended for this stage of work? | Version, approval, location, direction, and effective shift |
| Setup and inspection logs | Who checked the devices and what problems were found? | Actual inspection times, observations, and corrective action |
| Photographs and video | What could approaching drivers see before the impact? | Original files, camera position, recording time, and obstructions |
| Crew and equipment records | Where were workers and moving vehicles assigned? | Shift roster, task changes, equipment movements, and supervisor instructions |
| Messages and incident reports | Had someone reported a displaced sign, near miss, or traffic problem? | Recipient, timing, response, and whether the condition persisted |
| Contracts and daily sign-offs | Who undertook setup, inspection, maintenance, or correction? | Scope of work, subcontract assignments, and actual field performance |
Identify who took each photograph and whether anything had already moved. A later site visit can document road geometry, but it cannot by itself establish where a portable sign stood during the earlier shift. Label observations accordingly. No one should enter an active traffic lane to collect evidence.
Reconstruct the driver’s view and the worker’s movement
Obtain available dashcam footage, work-vehicle recordings, traffic-camera video, and vehicle data before routine deletion or repair makes collection harder. A preservation request should identify the road, direction, approximate time, and relevant vehicles or cameras. Ask for footage covering the approach and aftermath, with the original files and available timing information.
Compare the driver’s path with the warning signs, lane taper, lighting, queue, parked equipment, and worker position. Consider sightlines at the relevant time of day and whether another vehicle blocked a warning. Speed, attention, impairment, and the driver’s response remain part of the investigation even when traffic-control questions exist.
Worker movement also needs a careful account. Was the worker inside the assigned work space, approaching equipment, performing flagging duties, or crossing a travel path? Preserve the instructions, hazard assessment, and witnesses’ observations. A worker’s position alone does not explain why the vehicle reached that location.
A missing device or a departure from a plan needs a connection to the collision. Conversely, an apparently compliant diagram does not prove that the installation matched it or that conditions remained safe as the work changed. An appropriate reconstruction may need engineering analysis of the actual approach, available sight distance, and sequence of events.
Identify the parties before treating every contractor alike
List the road owner, prime contractor, traffic-control subcontractor, worker’s employer, and striking vehicle’s driver and owner. Determine their actual roles from agreements and field records. Responsibility for an inspection or correction should be traced to evidence; a name on a project sign does not resolve the claim.
Under R.S. 23:1101, receiving workers’ compensation does not itself eliminate a claim against a legally responsible third person outside the statutory exclusive-remedy protection. Whether a particular project participant qualifies for that protection requires a separate analysis. Compensation reimbursement and settlement requirements also need attention before resolving a third-party claim.
Our guide to workers’ compensation and third-party injury claims explains that interaction. The discussion of witness evidence helps distinguish what a person observed from what they learned later. Our Baton Rouge construction accident practice investigates site control and potential third-party responsibility.
Editorial & Legal Accuracy Notice (Louisiana)
Applicable traffic-control duties, compensation rights, and responsibility depend on the project, accident date, and evidence.